PML Shallow Transmission Pan Dodge-Jeep-Chrysler NAG 1

Starting at: $265.95

Many Chrysler, Dodge, Jeep, and Mercedes vehicles have the NAG1, 722.6 (W5A580, WA580, W5A380, W5J400) transmission so PML has designed three different pans for the transmission. PML designed this 722.6/NAG1 transmission pan for:
  • Cooling — fins and aluminum construction
  • Clearance — only 5/8 inch deeper than stock pan
  • Drain plug — on the side for safety
  • Secure seal — machined flat flange, no more retaining clips and formed gasket
  • Strength — high quality, thick walls

    Number of Bolts: 6

    Always check your vehicle to verify configuration and clearance!

    PML design this pan to work with the stock filter. The Mercedes part number on the filter PML used during design and development is 140 277 00 95. There are filter supports cast into the pan to hold the filter in place at the same level as the stock pan. The filter supports eliminate the need for an extension.

    It is the responsibility of the installer to verify filter and fitment.

    Gasket Information:

    PML offers a cork and rubber gasket for those who prefer a gasket over RTV. PML's pan is not compatible with the stock gasket. PML's gasket is not compatible with the stock pan. You can add this gasket to your order when you purchase this pan.

    Dipstick and Transmission Fluid Level:

    The fluid level should be at the same level in the stock pan and a PML pan. On many vehicles, the dipstick uses the bottom of the pan as a stop. PML pans have a ledge where the dipstick hits at the same level as the stock pan even though the PML pan is larger overall. In the above images of the inside of the pan, you can see the square ledge near the filter supports.

    Many vehicles with these transmissions do not have a dipstick and the correct fluid level is based on temperature. The cap for the transmission fluid fill and level check can say "See Dealer". The installer of a replacement pan needs to have the correct tools to replace the transmission fluid according to the factory instructions. PML does not provide a dipstick.

    Shield on Passenger's Front Corner:

    Some vehicles have a shield that attaches to the retaining clip at the front, passenger side corner of the stock pan. Pans available since March 2016 have a tab for the shield to bolt on to. If you have an older pan, you will need to fabricate a connector or slightly bend the shield to bolt onto the PML pan.

    Optional Machining for Temperature Sending Unit

    This pan has three locations that can be machined for a temperature sending unit. One location is on the driver's side and two are one the passenger's side of the pan. These locations are circular bosses and can accommodate between 1/8 NPT and 1/2 NPT. PML can drill and tap the hole to order for a $45 machining charge.

    PML Transmission Pan Features:

  • Increased oil capacity for cooler temperatures
  • Sand-cast aluminum with raised fins
  • 3/16-inch thick wall construction to add strength to the transmission case
  • 3/8-inch thick gasket flange will not bend when bolts are tightened
  • Machined gasket surface for a secure seal
  • Boss cast into pan can be machined for a temperature sensor
  • Drain hole and magnetic drain plug for easier, less messy maintenance

    All PML transmission pans ship with new mounting bolts and a magnetic drain plug.

    Transmission Fit: NAG 1

    Vehicle Fitment:

    Jeep:

  • 2002-2012 Jeep Grand Cherokee (02-04 WG Diesel W5J400, 05-10 WK V6, WH V6 3.0 Diesel export only Steyr W5A580)
  • 2006-2010 Jeep Commander XK (3.7 gas) XH (3.0 diesel - export)
  • 2012-Present Jeep Wrangler

    Dodge:

  • 2005-2008 Dodge Magnum (AWD, RT, SRT8 only)
  • 2006-2014 Dodge Charger (AWD, RT, SRT8 only) (2006-2007 3.5L V6 HO)
  • 2007-2011 Dodge Nitro (4.0L Models only)
  • 2009-2014 Dodge Challenger
  • 2011-2012 Dodge Durango (V6 Models only)

    Chrysler:

  • 2005-2014 Chrysler 300 (AWD, 300C, SRT8 only)
  • 2004-2008 Chrysler Crossfire, all models
  • 2004-2010 Chrysler 300 C CRD (with OM 642 V6 Diesel engine)

    This Item is available custom Powdercoated, hydro-dipped, factory painted, or polished for additional cost.

    For Factory Paint select "Factory Paint Match" in the "Billet Finish" menu, please enter your paint code.

    For custom hydro-dipping, please select "Custom Hydrodipped" in the "Billet

    For custom polishing, please select "Polished" in the "Billet Finish" menu.

    For custom powdercoating, please select "Powdercoated" in the "Billet Finish" menu, then select your color from the "Powdercoat Color" menu. Finish" menu, then contact us for the film you wish to use. We have access to 100's of films, so feel free to ask...


  • Add to Cart:

    • Model: PML 11132 NAG1 Transmission Pan
    • Shipping Cost: 25.95lbs
    • 1 Units in Stock
    • Manufactured by: PML Covers

    Please Choose:

    Add To Order










    This product was added to our catalog on Friday 18 January, 2019.

    Copyright © 2019 3rd Strike Performance. Powered by 3rd Strike Performance!