Cardone Reman Power Steering Pump 92-00 Dakota, 98-00 Durango

  • Model: Cardone 20-862 PS Pump Dodge
  • Shipping Cost: 15.95 shipping
  • 1Dropships direct from manufacturer
  • Manufactured by: Cardone

$45.95

Add to Cart:
Cardone remanufactured power steering pumps are among the highest quality remanufactured parts in the aftermarket. That's because they don't just replace components as needed. Through reverse engineering, their technicians pinpoint original equipment design weaknesses by examining failed cores.

Power Steering Pump Without Reservoir, Remanufactured, Replacement, 92-00 Dodge Dakota, 98-00 Dodge Durango, 92-93 Dodge D150, 92-93 Dodge Ramcharger

Features include:

  • All critical components are triple-tested to ensure reliability
  • All units are built with 100 percent new O-rings and premium-grade VitonĀ® seals to prevent leaks and avoid high-temperature breakdown
  • Every pump is computer-tested to measure pressure, bypass, fluid flow, valve operation, steering effort, and noise
  • Shafts are surfaced to precise specifications to eliminate premature seal wear and extend pump life
  • Units are supplied with 100 percent tested and calibrated pressure relief valves
  • Cardone remanufactured parts are business and environmentally friendly

    This part has an additional core charge of $15.00 per item. You can receive a refund by returning a suitable old core. Customer responsible for return shipping on core items. Please refer to the core return instructions included with the part or contact customer service for more details.

  • Power Steering Pump Model: Stock
  • Reservoir Included: No
  • Fittings Included: No
  • Inlet Attachment: Stock
  • Outlet Attachment: Stock
  • Power Steering Outlet Size: Stock
  • Pulley Included: No
  • Pump Flow: Standard-volume
  • Quantity: Sold individually.

    Notes: Due to core availability product appearance and finish may vary, but fit and function remain the same.

    Installation Information:

  • Inspect or change Power Steering Pressure and Return Hoses when replacing the power steering pump. Damaged hoses, or hoses that are at least 5 years old, should always be replaced
  • Where applicable, replace the Power Steering Reservoir or clean the internal filter
  • Use a Pulley Tool to remove the power steering pump pulley
  • Completely flush the system with an OE approved Power Steering Fluid prior to installation
  • Install an in-line Power Steering Filter to prevent contamination
  • Bleed the system to prevent noise and extend the life of the steering components (this may require a vacuum pump and Power Steering Bleeder Kit)

    Flush Procedure:

    Prior to replacing any power steering system component, the power steering system must be flushed before operation. Flushing removes old hydraulic fluid and contaminants in the power steering system that will cause accelerated wear or improper operation of the replacement unit. Follow the steps below to properly flush the system.

  • 1) Remove pressure and return lines from pump. Flush pump reservoir, return and pressure lines by pouring new fluid through components until fluid runs clear. Be sure to only use fluid recommended for your vehicle.
  • 2) Reconnect pressure line to pump and steering component. Reconnect return line only to steering component.
  • 3) Place return line from power steering unit into a drain pan. Cap return port on reservoir to prevent leakage.
  • 4) Fill power steering pump reservoir with NEW fluid recommended for your vehicle.
  • 5) Disable the engine so it will not start when cranked. Refer to vehicle service manual for correct procedure.
  • 6) Crank engine and continue to replenish fluid until fluid coming from return line has no air bubbles. NEVER LET THE POWER STEERING PUMP RUN DRY! Note: Do not crank engine for more than a few seconds at a time or starter will overheat.
  • 7) Install an in-line power steering filter in return line to increase the life of the power steering components. Connect the return line to the power steering pump, making sure all lines are properly torqued. Overtightening hydraulic lines will strip the threads. Failure to install a filter or properly torque fittings will VOID WARRANTY.
  • 8) Be sure fluid in pump reservoir is at proper operating level.
  • 9) Start the engine and turn the steering wheel from side to side 2 to 4 times to bleed the system.
  • 10) Refill reservoir to proper level if necessary.
  • 11) Check for smooth assist, excessive noise, connections for leakage and system for proper operation.

    Power Steering Pump Diagnosis:

    Steering issues can be caused by a variety of different parts on the vehicle and misdiagnosis is common. Typical symptoms of a bad Power Steering Pump include:

  • Leaking
  • Stiff steering while turning the wheel, especially at low speeds
  • Whining, groaning or squealing noises that increase when accelerating

    Dropships direct from manufacturer.

    Item Photo


  • This product was added to our catalog on Tuesday 20 April, 2021.

    Copyright © 2024 3rd Strike Performance
    Mobile Website by: Manor Media Group